CANBERRA MULTIPORT II DRIVER DOWNLOAD
When used in a timing system, the Model will enhance performance of moderate NaI to slow HPGe speed radiation detectors. For added convenience, the time display can be internally configured for either seconds or hours. SG1-R and SG2-R probes can show a sporadic saturation due to a timing conflict between the analog to digital conversions made in the probe The initialization time is now set to 30s instead of 20s. Precise repeatable performance is designed and built into the B. For the full-featured standard English-language product, right-click and choose “save target as” to download the appropriate file s to your computer:. A test input is provided to assist in system setup. The Multiport unit is suitable for use with a wide range of radiation detectors.
|Date Added:||26 April 2010|
|File Size:||13.97 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
The PUR circuit interrogates incoming pulses for pile up and generates a signal that prevents the ADC from converting the piled up events. Otherwise, sets the real-time preset to value.
A wide range of sample containers is supported to accommodate both raw and canned foods. The Asymmetrical mode virtually eliminates charge accumulation and correlated noise on the restorer holding capacitor and is especially suited for use with high resolution detector systems. In addition, it offers a choice of six front panel switch-selectable shaping canberea constants for each of the pulse shaping methods.
In the edconf configuration editor, possible MPII configurations include: The Amplifier offers six switch-selectable shaping time constants, which effectively doubles to 12 when the choice of Gaussian and Triangular are both considered, allowing optimum matching for most detector and count rate requirements.
This version is compatible only with Colibri hardware V1. Ethernet interface module B AIM. For the full-featured standard English-language product, right-click and choose “save target as” to download the appropriate file s to your computer: Units with fewer than six inputs can be field upgraded with additional inputs.
The versatility of the is further enhanced by a bipolar output for use in timing and gating applications. The rear panel also has a connector for signal input from an optional external test pulser.
SG1-R and SG2-R probes can show a sporadic saturation due to a timing conflict between the analog to digital conversions made in the probe The canbfrra time is now set to 30s instead of 20s. Many of their characteristics are discussed below. The pulse decays with a time constant of 50 ms for presentation to a main amplifier.
These widely recognized interfaces make the Multiport II compatible with a wide range of computer platforms, so the Multiport II user need not worry about compatibility as computer bus canbefra evolve.
RADIOC HEMISTRY LAP
If using Genie Version 3. And this new hardware is not compatible with the previous versions. The following prerequisites are required for this patch: To add French or German -language capabilities to the standard English-language product s downloaded above, right-click and choose “save target as” to download the appropriate file s to your computer; then place in the appropriate folders based on the English previously installed above:.
The Multiport II provides better performance and lower noise than plug-in PC board based MCAs by keeping all sensitive components out of the computer itself and by putting the MCA close to the radiation detectors.
The normal approach is to utilize one or more technicians to manually load and count multipoort samples to a fixed counting time. The DSA-LX offers peak gain stability at up to a factor of two to three times better than past generation analog products while Zero drift is barely measurable over multtiport full operating temperature range of the instrument.
The Multiport II is easy to install and easy to link. The gated baseline restorer automatically adjusts the restoration rate and threshold optimizing performance to the incoming count rate and system noise level.
Allowed values are, iii, and With the built in digital oscilloscope, the user views a graphical reconstruction of the digitized, filtered signal. This allows you to assemble a high resolution spectroscopy system without the energy rate limitations normally associated with RC preamplifiers. The output then provides a voltage in direct proportion to the collected charge at the rate of 0.
The B amplifier employs a simple gated baseline restorer which, because of its symmetrical characteristic, provides high resolution for HPGe detectors at low and high counting rates. In addition, the alternative use of most charged particle detectors is also supported.
A test input is provided to assist in system setup.
View the catalog Go to the Canberra Industries website for more information. This version is compatible with Colibri V2.
Package size and battery life set a new standard for field portability and convenience. The first stage acts as an operational integrator which produces an output potential proportional to the accumulated charge on the feedback capacitor Cf.